Changed timeout range and constraints to 1000 to 5000 ms. V2.0.2 Changed default timeout to 2 seconds. V2.0.3 Added DTR control support and 3 second delay for Mega2560 reset if enabled. V2.0.4 Fixes certain calls to syncToCoordinates() and slewToCoordinates() not setting targetRA/targetDec. Passes through more exceptions on connect. The timeout default is now 3s instead of 2s. The timeout setting default is now set correctly after install. V2.0.6 The setup dialog now uses the timeout setting when connecting over IP. V1.0.2 Fixed Telescope Meridian Limits not being disabled in Alt/Az mode. V1.0.3 Fixed IP Address so it's recalled between sessions. V1.0.4 Corrected Telescope UTC Offset handling. V1.0.6 Fixed Telescope Longitude upload failing for negative values to OnStep 3.16. V1.0.7 Allow Unpark to work even if not parked when OnStep is isn't in strict parking mode. V1.0.8 Locale fixes in the Telescope driver. #3s ip camera utility serialV1.0.9 More locale fixes, added 3s delay after serial connect when DTR control is enabled. Serial connect attempts three times instead of two. #3s ip camera utility driverV1.0.10 Switch driver detect absence of Auxiliary Features properly. V1.0.12 Added ASCOM Observing Conditions driver. V1.0.13 Better ASCOM Observing Conditions driver error handling. V1.0.14 Added Telescope DestinationSideOfPier() support and fixed compliance check axis move issues these require OnStep version 5.01 or later. Added Telescope Set SideOfPier() support require OnStep version 5.01 or later. V1.0.15 CommandBool() now handles slewing commands properly. V1.0.16 Telescope enable/disable using :Te# and :Td# only. V1.0.18 Corrected bug that prevented checksum communications from working. V1.0.19 Corrected Description and DriverInfo methods. V1.0.21 Allow OnStepX connection when no mount is present. V1.0.22 Fix for DestinationSideOfPier() and OnStepX. V1.0.23 Fix for get SiteLongitude() and setup dialog UTC Offset. V1.0.24 Allow MoveAxis rates from 0.0 deg/s up to OnStep's MaxRate at the time of connection. #3s ip camera utility downloadThe prior stable OnStep ASCOM driver, version 1.50, is available to download here. The current stable OnStep ASCOM driver, version 2.0.6, is available to download here. #3s ip camera utility driversThese new drivers are the result of many many hours of work, please consider making a Donation to help support the developer if you find them useful.įor versions of OnStep prior to release-3.16: These values are usually obtained from an attached BME280 device (otherwise it returns the default TPHD values.) This provides Temperature, Pressure, Humidity, and Dew-Point. The Observing Conditions driver is functional with OnStep version 3.16 or later.It does not support the INTERVALOMETER since that control doesn't logically map to ASCOM Switch capabilities. It also supports switching the DEW_HEATER's on/off. The Switch driver fully supports both SWITCH and ANALOG_OUT Auxiliary Features with OnStep version 4.17 or later.The Rotator driver is only functional with OnStep version 4.17 or later since the command protocol was enhanced in support of this driver.This driver can detect the swapped condition and make sure commands go to the designated focuser (if set to do so, requires OnStep 4.17 or later.) do this) so minimal controls can operate two focusers. OnStep has the ability to "swap" focusers (Android App, SHC, etc. The Focuser driver is functional with OnStep version 3.16 but TCF support (and backlash/deadband) requires version 4.17 or later.The Telescope driver is functional with OnStep version 3.16 or later.Any com (or IP) port (or ports) can be shared among all OnStep ASCOM drivers in this package. These drivers do not require using an ASCOM hub such as POTH for multipule connections.The prior OnStep Telescope and/or Focuser drivers will not be uninstalled automatically by this installer, you can however use Windows "Programs and Features" utility to remove them if you like though they will not interfear with this driver set. #3s ip camera utility freeReport problems and feel free to uninstall and switch to the prior stable drivers (links below.)
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |